manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 15

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Lower Arm (R / L) & Bearings & Pivot Shaft

NOTE: This instruction applies to all units, but units with S/N > 412137 have the
cam shown in Steps 7 & 25 and those lower do not.

Tools Required

½” socket and ratchet
Large flat head screwdriver
5/32" hex key
(3) 2x4 blocks of wood (Very helpful!)
Long Phillips screwdriver
Hard rubber or plastic hammer

Loctite 242
Grease/silicone (white/clear)
Torque wrench
Scratch awl
Safety glasses

2. Disconnect stabilizers or
support tubes from footpedals.

Remove both footpedals.

See 

Footpedal 1999 

and 

Footpedal

Support Tube 1999 

or 

Footpedal

2000 

and 

Footpedal Stabilizer 2000

instructions depending on your
model.

3. Remove step through support.

4.  For S/N < 428173, disconnect
timing belt springs.  

See 

Timing Belt

Springs 

instruction.

42001 Arm - Lower 5-1-05

 

7

5. Remove left and right side nuts
that attach rod ends to arms.

 

1. Remove covers.  

See 

Cover

Removal

 instruction.

To avoid injury, wear safety glasses.

!

 CAUTION

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands