Nustep TRS 4000 Service Manual Download Page 23

Page: 23 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Position Indicator Label Replacement

Tools Required

Rubbing alcohol

1. Remove old label. Clean label
area with rubbing alcohol and let
dry.

No photo.

2. Expose one inch of new label.
Attach this edge to forward bottom
corner of non-textured area on left
side of cover.

3. Remove remainder of adhesive
backing while holding front edge of
label down.

No photo.

4. Carefully align label along bottom
edge of non-textured area. NOTE:
Do not pull hard on label while doing
this, otherwise it will stretch!

5. Gently smooth label down. Don’t
press down too hard the first time or
bubbles and creases may develop.

6. Align Seat Position Indicator if
needed.

See

Seat Position Indicator

instructions.

No photo.

42087 Seat Position Indicator Label 9-18-00

Summary of Contents for TRS 4000



































































































































Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands

Nustep TRS 4000, Service Manual

Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands