manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 71

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

63

VR Sensor

NOTE:  The VR sensor and the magnet that passes by it are responsible for indicating WATTS,
METS, CALORIES, and TIME on the display.

Tools Required

Phillips screwdriver

2. Disconnect ribbon cable.

 

It makes it easier to access wire.

3. Disconnect VR sensor wire.

 

4. Unscrew sensor bracket from frame.

5. Remove sensor wiring from cable clips along frame.

 

Note: Bottom view shown.

42107A VR Sensor 5-01-05

 

 

 

 

The black & white wire on left.

 

 

The photo above shows the sensor bracket
used for serial numbers 411001 - 422080.

The photo above shows the sensor bracket
used for serial numbers > 422081.

The TRS 4000 is very heavy; it weighs
205 lbs (93 kg). To avoid injury, or
damage to the product, always obtain
assistance to move this product. Use
proper lifting technique.

!

 CAUTION

1. Remove covers.  

See 

Cover Removal 

instruction.

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands