manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 119

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Swivel Release Lever

42099 Swivel Release Lever 5-1-05

7. To install seat channel, place Loctite on swivel bolts.

 

5. Lift seat channel assembly off.  Remove swivel release lever.

 

6. Install new swivel release lever and tighten to 80 in-lbs.

 

Note:  for S/N’s 415412 - 421171, install
lever using flange nuts provided with new
lever.  Do not install lever with washers
and jam locknuts.

To avoid injury and prevent adverse
health effects, use Loctite in
accordance with the manufacturer’s
material safety data sheets, including
the use of safety glasses and
impermeable gloves. Material safety
data sheets are available via the
internet at 

www.loctite.com 

or by

calling Henkel Corporation at (800) 562-
8483.

!

 CAUTION

80 inch-lbs

Torque Setting:

111

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands