Nustep TRS 4000 Service Manual Download Page 79

Page: 79 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Note: This only applies to units with serial numbers

≥

413368. For serial numbers 411001 –

413367, see Footpedal 1999 instructions. Left side instructions are shown.

Footpedal 2000 (R or L)

Tools Required

3/16" hex key

Loctite 242

½” wrench

Large flat head screwdriver

Snap ring pliers - 90

tip

Safety glasses

1. Remove upper nut from stabilizer. Prevent shoulder bolt from turning.

2. Pry rod end off shoulder bolt with
large flat head screwdriver.

Shoulder bolt is locked to footpedal. Don’t
turn it. If it loosens, then Loctite it back in
during installation below.

3. Remove upper footpedal retaining
ring and remove footpedal.

42041 Footpedal 2000 5-01-05

To avoid injury, wear safety glasses.

CAUTION

Summary of Contents for TRS 4000



































































































































Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands

Nustep TRS 4000, Service Manual

Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands