manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 25

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Display Removal / Installation

Tools Required

Phillips screwdriver

1. Slide boot down tube and remove
three screws.  Hold onto display
before removing third screw so it
doesn’t fall!

2. On back of display, push 2
locking tabs outward on each side
of connector to unlock cable
connector.

 

 

3. Hold onto cable connector and
pull outward from display
connector.

4. To install, align key on cable
connector with slot on display
connector.               

Slot

 

 

5. Push 2 locking tabs inward until
they snap in place to secure cable.

6.  Hold onto display so it doesn’t
fall, install three screws, slide boot
up.  Check display operation.

 

 

 

 

                               

  Key

 

 

42023 Display Removal 9-8-00

17

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands