manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 102

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Mounting Bracket & Seat Release Lever Bracket &
Swivel Release Lever Bracket & Springs & Nyliners

42083 Seat Mounting Brkt & Levers 5-1-05

6. Remove shoulder bolts and
remove swivel release lever bracket
assembly.

7. Replace springs or Nyliners now.
Lubricate and install springs with
larger diameter coil against seat (in
holes).  If only replacing springs or
Nyliners, GOTO Step 12.

Insert Nyliners with large flange out.

 

 

 

94

8. Transfer old lever to new bracket.  Place Loctite on bolts if applicable.
Tighten bolts or nuts to 80 in-lbs. GOTO Step 12.

 

Note: for S/N < 415411 the
lever is attached with bolts.
For S/N > 415412, the lever is
attached with nuts.

To avoid injury and prevent adverse
health effects, use Loctite in
accordance with the manufacturer’s
material safety data sheets, including
the use of safety glasses and
impermeable gloves. Material safety
data sheets are available via the
internet at 

www.loctite.com 

or by

calling Henkel Corporation at (800) 562-
8483.

!

 CAUTION

80 inch-lbs

Torque Setting:

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands