manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 26

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

42131 123GO/RR/H20 Instruction 2-6-04

This instruction applies to the Water Bottle Holder (PN 4300), the Reading Rack (PN 4305) and
the 123GO! Instruction Panel (PN 4310).  The three accessories may be ordered together as
the Display Accessory Kit (PN 4315).  Note: the water bottle shown below is not available.

Tools Required

Phillips screwdriver

Attach accessories to back of display using provided screws.  Note:
when the display accessory kit is shipped with a TRS4000 Recumbent
Cross Trainer, the screws are preinstalled in the back of the display.
Remove the screws and use them to attach the accessories.

123GO! Instruction Panel

Reading Rack

Water Bottle Holder

 

 

 

Installation Instructions for Water Bottle Holder, Reading Rack and
123GO! Instruction Panel

18

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands