manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 100

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Mounting Bracket Assembly

42263 Seat Mounting Bracket Assembly 5-01-05

16. Install seat release bracket.

For S/N < 428341, see 

Seat Release Bracket

 instructions.

For S/N > 428342, see 

Seat Release Bracket With Stud 

instructions.

92

13. Swivel assembly 90

°°°°°

 to install next two bolts through cutouts.

 

15. Check swivel lever operation.  Swivel seat left and right and check that
swivel locks in place.

 

14. Tighten all four bolts to 200 in-lbs.

 

To avoid injury, and to ensure safe
operation of this product, fasteners
must be tightened to the proper torque.

!

 CAUTION

17. Check seat locking operation.  Install seat assembly onto NuStep.

See 

Seat Assembly Removal 

instructions.

200 inch-lbs

Torque Setting:

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands