manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 111

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat Release Bracket With Stud & Seat Release Spring

Tools Required

5/32" hex key

Needle nosed pliers

1/2” socket and ratchet

Phillips  screwdriver

Silicone or white grease

Safety glasses

1. Remove seat assembly.  

See 

Seat Assembly Removal 

instructions.

2. Remove seat release bracket by removing front locknut, front flange
bearing, and rear shoulder bolt (keep rear washer and bolt).

42091A Seat Release Bracket Instruction 5-1-05

 

 

3. Remove and keep seat release
spring.

NOTE: This instruction applies to units with S/N > 428342.

To avoid injury, wear safety glasses.

!

 CAUTION

4. Remove old thrust washer from
seat release bracket.

Springs are under tension. To avoid
injury, or damage to the product, use
caution when removing or installing.

!

 CAUTION

103

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands