manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 90

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Seat & Swivel & Seat Channel

5. Lift seat channel assembly off.
NOTE: If you are replacing the seat
channel or swivel, GOTO Step 10.

6. Remove seat mounting bracket.
Remove front two bolts below and
lift assembly off seat.

7. Replace seat.  Lubricate seat
bottom lightly where it contacts
mounting bracket (see old seat).
Transfer armrests to new seat.

8. Position springs with larger
diameter coil against seat.  Install
mounting bracket over both springs.
Springs go through holes in bracket.

Lubrication prevents squeaking be-
tween the two parts.

Springs shown in holes (other parts re-
moved for clarity).

 

 

 

 

42077 Seat & Swivel & Seat Channel 5-01-05

 

82

10. Remove four bolts that
attach swivel to channel.

 

200 inch-lbs

Torque Setting:

9. Align 6 mounting holes, install
front two bolts, tighten to 200 in-lbs.
GOTO Step 13 if you are done.

Make sure
springs
operate
properly.

 

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands