Nustep TRS 4000 Service Manual Download Page 44

Page: 44 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Poly-V J6 Flex Belt & Sheave Without Grooves

Tools Required

5/32" hex key

2 zip ties (PN 30586)

Diagonal cutters or tin snips

1. Remove covers.

See

Cover Removal

instructions.

2. To remove belt, run belt off poly-v sheave.

42068 Poly-V J6 Flex Belt & Sheave Without Grooves 5-1-05

3. Note: If you are just replacing the belt, GO TO Step 6.
No photo.

4. Note location of poly-v sheave on
shaft and loosen 2 set screws to
remove poly-v sheave.

5. Install new poly-v sheave on shaft
in similar position as old one. Do
not tighten set screws.

Note: This instruction only applies to units with S/N > 428326.

Belt is under tension. To avoid injury, or
damage to the product, use caution
when removing or installing.

CAUTION

Summary of Contents for TRS 4000



































































































































Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands

Nustep TRS 4000, Service Manual

Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands