manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 35

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

42015 Connecting Link 5-1-05

Connecting Link

…and do the same on rear.  Don’t
get Loctite on rod end balls.

 

 

9. Place rod ends onto shoulder
bolts, and tighten nuts to 200 inch-
lbs.

10. On both rod ends, wipe grease
on both sides of rod end into spaces
between rod end and washer, and
rod end and nut.

11. Slide boots down, test operation and install covers.  No photo.

 

27

8. Place a few drops of Loctite 242
on front shoulder bolt and threads...

 

To avoid injury and prevent adverse
health effects, use Loctite in
accordance with the manufacturer’s
material safety data sheets, including
the use of safety glasses and
impermeable gloves. Material safety
data sheets are available via the
internet at 

www.loctite.com 

or by

calling Henkel Corporation at (800) 562-
8483.

!

 CAUTION

200

inch-lbs

Torque

Setting:

 

7. Pry rear rod end off shoulder bolt
with large screwdriver.

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands