manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 55

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

EC Ball Plunger Replacement / Adjustment

Tools Required

Flat head screwdriver

1. Remove covers.  

See 

Cover Removal

 instruction.

2. Place workload lever in position 4.

3. NOTE: If you are just adjusting
ball plunger GOTO Step 4.  If
replacing, remove old one and
replace with new one.

 

4. Tighten ball plunger until ball just
seats into each hole on plate.

NOTE: Move workload lever back and
forth and then adjust ball plunger.
If workload lever is too tight (lever
moves hard, and body of ball plunger
scrapes plate), loosen ball plunger by
turning a little to the left.
If workload lever is too loose (there is a
little “play” in each position), tighten ball
plunger by turning a little to the right.
The right “feel” is achieved when the
workload lever hits each position, but is
not too hard to move or has excessive
“play.”

 

5. Test that all 10 Workload Levels
show on display.  No photo.

6. Install covers.  No photo.

42025 EC Ball Plunger 9-10-00

47

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands