Nustep TRS 4000 Service Manual Download Page 65

Page: 65 / 130

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Workload Level PCB

Tools Required

Parts Required

Scratch awl

(4) 1/8" diameter by 5/16" length pop rivets

Hammer

Safety glasses

Pop rivet gun

3. Disconnect wires from back of
PCB.

4. From outside of frame, pound out
rivets using scratch awl & hammer.

5. Remove PCB and insulator board
from frame.

No photo.

6. Carefully install new PCB and
insulator board between wiper and
frame using pop rivets. (see
reference photo below before
proceeding).

8. Test all electronics before
installing covers.

7. Reconnect wires shown in Step 3.

Reference Photo:

Workload PCB

NOTE: EC Plunger shown removed
from frame for clarity. It is not
necessary to remove plunger to install
PCB, but you must be careful when
installing PCB.

Insulator board Wiper

42111 Workload Level PCB 5-01-05

1. Remove covers.

See

Cover

Removal

instruction.

2. Put workload lever in load 1.

To avoid injury, wear safety glasses.

CAUTION

Summary of Contents for TRS 4000



































































































































Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands

Nustep TRS 4000, Service Manual

Search results

Summary of Contents for TRS 4000

Reviews:

Brands by name

Popular brands