manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 73

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Electronic Tube

Tools Required

Phillips screwdriver

Wood block

½” wrench

Torque wrench

1. Remove three screws - and hold
onto display so it doesn’t fall!

2. Release 2 locking tabs on each
side of connector.

 

 

Slide boot down tube, then remove
1 screw each side, 1 on bottom.

Snap tabs of connector outward.

3. Pull out cable from connector.

4. Slide both rubber boots up and off
electronic tube.
No photo.

 

5. Remove 4 bolts that attach
electronic tube and remove tube
from frame carefully letting ribbon
cable come out end.

6. To install, tie washers on end of
string and drop from top through
tube.  Tie ribbon cable to string and
carefully pull up through tube.

 

 

Remove front cover screw and
carefully spread covers to access bolts.

String with washers attached to ribbon
cable

 

 

42035 Electronic Tube 5-01-05

65

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands