manualshive.com logo in svg

Nustep TRS 4000, Service Manual

Share
Download
Nustep TRS 4000 Service Manual Download Page 19

TRS 4000

[email protected] - (800) 322-4434 - (734) 769-3939 x 5

[email protected] - (800) 322-4434

Lower Arm (R / L) & Bearings & Pivot Shaft

42001 Arm - Lower 5-1-05

25. Set cams to eliminate “play”
from arms.  Insert scratch awl into
hole with slight pressure.  While
keeping pressure on awl, tighten
screws with hex key.

26. Insert plugs, install covers and slide boots back in place.  No photo.

NOTE: Cams are set correctly when
“play” is removed from arms, but cam is
not set too tightly, which can increase
arm resistance.

 

 

11

22. Place rod ends onto shoulder
bolts and tighten nuts to 200 inch-
lbs.

23. Wipe grease on both sides of rod
ends into spaces between rod end
and washer and rod end and nut.

24. Attach footpedals, stabilizers (or
footpedal tubes) and then attach
springs.
No photo.

 

 

200 inch-lbs

Torque Setting:

Summary of Contents for TRS 4000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands