31
Initial Setup
3.
ICP behind an HTTP Proxy Server:
The MiSync client uses HTTPS
to communicate with the AMC. The HTTP/1.1 CONNECT method is
the standard used by proxy servers to proxy HTTPS. There should be
no extra configuration work required. See Step 4, “SI Host PC behind
an HTTP Proxy Server” on page 30.
4.
CXi, CXi II, MXe-Specific WAN Considerations:
Program the
Internet Gateway (WAN interface) IP address details (see "MXe
Server/MXe/AX/CXi/CXi II Requirements for IP Networking" on
page 272).
Automatic Sync with AMC via MCD Software Installer
Tool (Rel 6.0 or later)
1.
Launch the Software Installer and select either the
MXe Server
check
box or the
3300 ICP
check box to get to the Login Dialog.
2.
Enter the Iogin information and the IP addresses. Click
Configure
.
3.
Perform one of the following:
-
If the software load you need is a higher release than the software
that is pre-loaded on the MXe Server’s hard drive, or if you are
installing software on a 3300 ICP, click
Perform Upgrade
.
-
If the pre-installed software on the MXe Server is the latest release,
click
License and Restore
, and then click
Perform Full Install
.
4.
Specify the IP address username and password of the FTP server, or
if you are using the 3300 FTP server, type in or browse to the location
of the upgrade software.
5.
Do one of the following:
-
If you selected
Perform Upgrade
in Step 3 of this procedure, then
click
Next
to proceed to the
Define Upgrade Options
screen.
-
If you selected
Perform Full Install
in Step 3 of this procedure,
click
Next
and then skip to Step 14.
6.
In the
Define Upgrade Options
dialog, specify the Backup
requirements and ensure that the License and Option Configuration
box is checked.
7.
Click
Next
to proceed to the
License and Options Selection
screen.
Tip:
If the SI is connecting to the MXe from behind a firewall, the firewall must
be configured to allow https (443), ftp (20, 21), and ssh (22).
Note that a DNS server is required.
Summary of Contents for 3300
