Mitel 3300 Technician'S Handbook Download Page 317

Page: 317 / 431

307

Typical Network Configurations

CXi/CXi II/MXe/MXe Server Configuration

Firewall/Port Forwarding

The Port Forward Table form allows external traffic to reach resources on
the internal network and can contain up to 40 entries.

PPTP Remote Access

The PPTP form is used to program the internet gateway as a PPTP (Point
to Point Tunneling Protocol) server for a remote client on the internet.

WAN Settings (Internet Gateway)

The WAN Settings form is used to enable the WAN interface and provide
internet connectivity settings.

•

Enable WAN Access

•

Select a WAN IP method: Static IP Address, DHCP Client, or PPPoE.

Table 64: Port Forward Table (CXi/CXi II/MXe/MXe Server only)

Parameter

Function/Values

Protocol

The WAN interface protocol; UDP or TCP.

Src Start Port

The source port at the start of the range.

Src End Port

The source port at the end of the range.

Dst IP Address

IP Address of the destination device.

Dst Start Port

Destination port at the start of the range.

Dst End Port

Destination port at the end of the range.

Table 65: PPTP (CXi/CXi II/MXe/MXe Server only)

Parameter

Function/Values

User Name

The username that the server uses to authenticate the
remote client.

Password

Password that the server uses to authenticate the remote
client.

Client IP Address

Address that the remote PPTP client uses on the LAN.

PPTP Access

Set to “Enable” to enable PPTP remote access.

Tip:

Refer to the Network Configuration chapters in the

3300 ICP

Engineering Guidelines

Summary of Contents for 3300
















































































































































































































































































































































































































































Search results

Summary of Contents for 3300

Reviews:

Related manuals for 3300

Brands by name

Popular brands

Mitel 3300, Technician'S Handbook

Search results

Summary of Contents for 3300

Reviews:

Related manuals for 3300

Brands by name

Popular brands