Lenovo x3250 m6 Installation And Service Manual Download Page 414

Page: 414 / 696

4. Replace DIMM n. (n = DIMM number)

•

81010002-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower non-critical)

has deasserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Non-critical sensor
going low has deasserted.

May also be shown as 810100020701ffff or 0x810100020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0477

User Response

No action; information only.

•

81010202-0701ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (CMOS Battery)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102020701ffff or 0x810102020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

400

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands