Lenovo x3250 m6 Installation And Service Manual Download Page 135 | Manualshive

Page: 135 / 696

background image

Step 5.

Install a new front I/O assembly. See “Installing the front I/O assembly” on page 121.

Installing the front I/O assembly

The front I/O assembly contains an operator information panel and two cables. If you have removed the front
I/O assembly, install a new one before turning on the server.

To install the front I/O assembly, do the following:

Step 1.

Carefully push the front I/O assembly into the server as shown until the front I/O assembly clicks
into place.

Figure 54. Front I/O assembly installation

Step 2.

Reconnect the USB cable and the operator information panel cable to the connectors on the
system board. Make sure the relevant cables pass through the cable clips.

Step 3.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Removing the operating temperature enhancement kit

To remove the operating temperature enhancement kit, do the following:

Step 1.

Turn off the server. Then, disconnect all external cables and remove all peripheral devices.

Step 2.

Remove the server cover. See “Removing the server cover” on page 88.

Step 3.

Remove the PCI riser-card assembly. See “Removing the PCI riser-card assembly” on page 93.

Step 4.

Disconnect the operating temperature enhancement kit connector from the system board.

Removing and installing server components

121

«
...
133
134
135
136
137
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: Mako Pages: 56

Brand: NComputing Pages: 95

Brand: G-Technology Pages: 35

NEAX2000 IVS Series

Brand: NEC Pages: 160

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 74

NOP1840 PEP-Box

Brand: Newtec Pages: 96

Brand: X-media Pages: 10

SUPERSERVER 5017C-MF

Brand: Supero Pages: 96

E7210 Master-FARM

Brand: MSI Pages: 34

Brand: Cabletron Systems Pages: 100

Brand: Ericsson Pages: 159

Brand: Vxl Pages: 2

Brand: Promise Technology Pages: 80

Brand: Viavi Pages: 8

Brand: Black Box Pages: 66

Brand: Vitek Pages: 2

Brand: Measy Pages: 15

TalkAnytime TA410

Brand: Multitech Pages: 209

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands