manualshive.com logo in svg

Lenovo x3250 m6, Installation And Service Manual

The Lenovo x3250 m6 is a versatile and reliable server with exceptional performance. To assist users in setting up and maintaining this powerful device, an Installation and Service Manual is available for free download. Find it on our website manualshive.com, ensuring a smooth installation and hassle-free service experience.

Share
Download
background image

41

CIM Information

Prefix:

PLAT

ID:

0132

User Response

1. Make sure the server meets the minimum configuration to start (see Power-supply LEDs).

2. Update the server firmware on the primary page. Important: Some cluster solutions require

specific code levels or coordinated code updates. If the device is part of a cluster solution, verify
that the latest level of code is supported for the cluster solution before you update the code.

3. (Trained technician only) Replace the system board.

Firmware Error : Sys Boot Status :

•

806f000f-220103ff : The System [ComputerSystemElementName] encountered firmware error -

unrecoverable boot device failure. (ABR Status)

This message is for the use case when an implementation has detected that System Firmware Error
Unrecoverable boot device failure has occurred.

May also be shown as 806f000f220103ff or 0x806f000f220103ff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0770

User Response

This is a UEFI detected event. The UEFI(POST) error for this event can be found in the logged IMM
message text. Please refer to the UEFI(POST) error code in the "UEFI(POST) error code" section of
the Information Center for the appropriate user response. Firmware Error : Sys Boot Status :

•

806f000f-220104ff : The System [ComputerSystemElementName]has encountered a motherboard

failure. (ABR Status)

This message is for the use case when an implementation has detected that a fatal motherboard failure in
the system.

May also be shown as 806f000f220104ff or 0x806f000f220104ff

322

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

IBM 5100 Installation Manual preview
5100
Brand: IBM Pages: 64
Paradyne FrameSaver SLV 9126 Installation Instructions Manual preview
FrameSaver SLV 9126
Brand: Paradyne Pages: 24
IBM NetVista N2800e Reference Manual preview
NetVista N2800e
Brand: IBM Pages: 82
IBM BladeCenter PN41 Problem Determination And Service Manual preview
BladeCenter PN41
Brand: IBM Pages: 88
IBM X 330 Series Installation Manual preview
X 330 Series
Brand: IBM Pages: 76
Data-Tronix DT-HDIPCOM Installation & Configuration Manual preview
DT-HDIPCOM
Brand: Data-Tronix Pages: 29
Data-Tronix DT-HDIPUS User Manual & Installation Manual preview
DT-HDIPUS
Brand: Data-Tronix Pages: 30
Acrosser Technology AND-APL1E Series User Manual preview
AND-APL1E Series
Brand: Acrosser Technology Pages: 42
Epson C823781 Software Installation Manual preview
C823781
Brand: Epson Pages: 28
Epson EpsonNet 802.11b Product Support Bulletin preview
EpsonNet 802.11b
Brand: Epson Pages: 30
Epson Stylus C80WN - Ink Jet Printer Hardware preview
Stylus C80WN - Ink Jet Printer
Brand: Epson Pages: 1
Epson C823781 Administrator'S Manual preview
C823781
Brand: Epson Pages: 258
Epson C82378 Administrator'S Manual preview
C82378
Brand: Epson Pages: 280
Fujitsu PRIMERGY BX620 S5 Options Manual preview
PRIMERGY BX620 S5
Brand: Fujitsu Pages: 50
Fujitsu PRIMERGY BX620 S4 Operating Manual preview
PRIMERGY BX620 S4
Brand: Fujitsu Pages: 81
Fujitsu PRIMERGY BX900 S1 Service Supplement Manual preview
PRIMERGY BX900 S1
Brand: Fujitsu Pages: 46
Fujitsu PRIMERGY BX620 S6 Options Manual preview
PRIMERGY BX620 S6
Brand: Fujitsu Pages: 56
Fujitsu Primergy BX920 S4 Operating Manual preview
Primergy BX920 S4
Brand: Fujitsu Pages: 66

Brands by name

Popular brands

Load more brands