Lenovo x3250 m6 Installation And Service Manual Download Page 140 | Manualshive

Page: 140 / 696

background image

Step 5.

Insert the fan into the bracket. Then, route the fan cable into the fan cable slot in the fan bracket.
Make sure that each of the gray soft tabs on the fan is fully seated in its slot in the fan bracket.

Figure 62. System fan installation

Step 6.

Connect the new fan cable to the system board. To locate the fan connectors on the system board,
see “System-board connectors” on page 21.

Step 7.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Removing the coin-cell battery

The following tips describe information that you must consider when removing the coin-cell battery.

• Lenovo has designed this product with your safety in mind. The lithium coin-cell battery must be

handled correctly to avoid possible danger. If you replace the coin-cell battery, you must adhere to the
following instructions.

Note:

In the U.S., call 1-800-IBM-4333 for information about battery disposal.

• If you replace the original lithium battery with a heavy-metal battery or a battery with heavy-metal

components, be aware of the following environmental consideration. Batteries and accumulators that
contain heavy metals must not be disposed of with normal domestic waste. They will be taken back
free of charge by the manufacturer, distributor, or representative, to be recycled or disposed of in a
proper manner.

• To order replacement batteries, call 1-800-IBM-SERV within the U.S., and 1-800-465-7999 or

1-800-465-6666 within Canada. Outside the U.S. and Canada, call your support center or business
partner.

Note:

After you replace the coin-cell battery, you must reconfigure the server and reset the system

date and time.

CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery

126

Lenovo System x3250 M6 Installation and Service Guide

«
...
138
139
140
141
142
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: IBM Pages: 151

SUPERSERVER 6021F

Brand: Supermicro Pages: 116

Portbase PB-3010

Brand: SystemBase Pages: 45

Brand: IBM Pages: 51

Brand: RackSolutions Pages: 8

8676 - Eserver xSeries 335

Brand: IBM Pages: 172

SuperServer 6019P-WT

Brand: Supermicro Pages: 133

Brand: Airlink101 Pages: 36

PRIMERGY CX120 S1

Brand: Fujitsu Pages: 82

PRIMERGY BX922 S2

Brand: Fujitsu Pages: 106

PRIMERGY BX924 S3

Brand: Fujitsu Pages: 290

PRIMERGY BX924 S4

Brand: Fujitsu Pages: 286

PRIMERGY BX924 S3

Brand: Fujitsu Pages: 64

Brand: Time Machines Pages: 24

Brand: ICP DAS USA Pages: 59

Brand: TAG Pages: 84

Brand: TRENDnet Pages: 3

Brand: Octagon Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands