Lenovo x3250 m6 Installation And Service Manual Download Page 169 | Manualshive

Page: 169 / 696

background image

Step 2.

Connect cables to the power distribution board.

Step 3.

Install the power distribution board cover. See “Installing the power distribution board cover” on
page 152.

Step 4.

Connect the cables to the power supply connector, microprocessor power connector, and power
distribution board connector on the system board. See “System-board connectors” on page 21.

Attention:

When connecting the cable to the system board, do not grab the wires. Grab the

connector to vertically connect the cable to the system board.

Figure 94. Connecting the power cable connector to the system board

Step 5.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Removing the system board

Before you start, notice the following information:

• After you replace the system board, you must either update the server with the latest firmware or restore

the pre-existing firmware that the customer provides on a CD image. Make sure that you have the latest
firmware or a copy of the pre-existing firmware before you proceed.

• When you replace the system board, make sure that you remove the Integrated Management Module II

(IMM2) Advanced Upgrade and place it on the new system board. .

• Before you replace the system board, make sure that you back up any Features on Demand (FoD) keys

that were enabled. Reactivate FoD after replacing the system board. To activate FoD and install activation
keys automatically, refer to the instructions in the

Lenovo Features on Demand User's Guide

. To download

the document, go to http://www.ibm.com/systems/x/fod/, log in, and click

Help

.

Note:

After you remove the system board, you need to install a new one. See “Installing the system board”

To remove the system board, do the following:

Step 1.

Turn off the server. Then, disconnect all external cables and remove all peripheral devices.

Step 2.

Remove the server cover. See “Removing the server cover” on page 88.

Step 3.

Remove the air baffle. See “Removing the air baffle” on page 90.

Step 4.

Remove the PCI riser-card assembly. See “Removing the PCI riser-card assembly” on page 93.

Step 5.

Record where the cables are connected to the system board; then, disconnect them.

Attention:

Disengage all latches, cable clips, release tabs, or locks on cable connectors

beforehand. See “Internal cable routing” on page 158. Failing to release them before removing

Removing and installing server components

155

«
...
167
168
169
170
171
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Express5800/T110g-S

Brand: NEC Pages: 34

HS12 - BladeCenter - 8028

Brand: IBM Pages: 204

NetVista N2800e

Brand: IBM Pages: 82

N2400 - TaskSmart - 1 GB RAM

Brand: Compaq Pages: 372

xSeries 342 2RX

Brand: IBM Pages: 158

Brand: Hitachi Pages: 58

Brand: Hitachi Pages: 192

Brand: Acer Pages: 20

Brand: Acer Pages: 20

AR360 F1 Series

Brand: Acer Pages: 20

Brand: Acer Pages: 18

AR380 F1 Series

Brand: Acer Pages: 17

Brand: Acer Pages: 134

Brand: Acer Pages: 23

AT350 F1 Series

Brand: Acer Pages: 23

Brand: Acer Pages: 160

Brand: Acer Pages: 95

AT350 F2 Series

Brand: Acer Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands