Lenovo x3250 m6 Installation And Service Manual Download Page 350 | Manualshive

Page: 350 / 696

background image

User Response

Note: Each time you install or remove a DIMM, you must disconnect the server from the power
source; then, wait 10 seconds before restarting the server.

1. Refer to TIP H212293 for minimum code level.

2. Check the Lenovo support website for an applicable retain tip or firmware update that applies

to this memory error.

3. Swap the affected DIMMs (as indicated by the error LEDs on the system board or the event

logs) to a different memory channel or microprocessor.

4. If the problem follows the DIMM, replace the failing DIMM.

5. (Trained technician only) If the problem occurs on the same DIMM connector, check the DIMM

connector. If the connector contains any foreign material or is damaged, replace the system
board.

6. (Trained technician only) Remove the affected microprocessor and check the microprocessor

socket pins for any damaged pins. If a damage is found, replace the system board.

7. (Trained technician only) Replace the affected microprocessor.

8. Manually re-enable all affected DIMMs if the server firmware version is older than UEFI v1.10.

If the server firmware version is UEFI v1.10 or newer, disconnect and reconnect the server
to the power source and restart the server.

9. (Trained Service technician only) Replace the affected microprocessor.

•

806f010c-2581ffff : Uncorrectable error detected for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (All DIMMS)

This message is for the use case when an implementation has detected a Memory uncorrectable error.

May also be shown as 806f010c2581ffff or 0x806f010c2581ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Memory

SNMP Trap ID

41

CIM Information

Prefix:

PLAT

ID:

0138

User Response

Note: Each time you install or remove a DIMM, you must disconnect the server from the power
source; then, wait 10 seconds before restarting the server.

1. Refer to TIP H212293 for minimum code level.

2. Check the Lenovo support website for an applicable retain tip or firmware update that applies

to this memory error.

336

Lenovo System x3250 M6 Installation and Service Guide

«
...
348
349
350
351
352
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Z10 BUISNESS CLASS Z10 BC

Brand: IBM Pages: 67

x3450 - System - 7948

Brand: IBM Pages: 2

Brand: Sun Fire Pages: 66

StorTrends 1312-P

Brand: American Megatrends Pages: 2

APSolute Vision

Brand: Radware Pages: 81

Brand: Watchguard Pages: 32

Sun Fire X2100 M2

Brand: Sun Microsystems Pages: 128

Brand: Sollae Systems Pages: 45

Brand: IBM Pages: 100

imagePRESS Server G200

Brand: Canon Pages: 98

imagePRESS A3200

Brand: Canon Pages: 192

ColorPass-Z7400

Brand: Canon Pages: 210

LaserJet 4200/n

Brand: HP Pages: 28

Jetdirect 2700w

Brand: HP Pages: 43

Jetdirect 2900nw

Brand: HP Pages: 20

LaserJet 4200/n

Brand: HP Pages: 36

wp110 - 802.11b Wireless Print Server

Brand: HP Pages: 35

JetDirect Ew2500

Brand: HP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands