Lenovo x3250 m6 Installation And Service Manual Download Page 652

Page: 652 / 696

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-902-000 : Optical Drive Test Failed

Optical Drive Test Failed. Read miscompare.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-903-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Could not access the device.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

638

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands