Lenovo x3250 m6 Installation And Service Manual Download Page 187 | Manualshive

Page: 187 / 696

background image

4. Reconnect the power cords.

5. Update the server configuration.

a. Save the new configuration settings when starting the server for the first time after you add or

remove a device. The Setup Utility program starts automatically.

b. Install device drivers for some optional devices. See the documentation that comes with each device

c. Reconfigure the disk arrays if you have installed or removed an HDD and a RAID adapter. See the

documentation that comes with the RAID adapter

d. Configure the Ethernet controller, see “Ethernet controller information” on page 38.

6. Start the server. Confirm that it starts properly and recognizes the newly installed devices, and make

sure that no error LEDs are lit.

7. For Business Partners only: Complete the additional steps in “Instructions for Business Partners” on

Instructions for Business Partners

This topic provides instructions for Business Partners on verifying the newly installed devices by running
the Dynamic System Analysis (DSA) stress test.

In addition to the instructions in this chapter for installing optional hardware devices, updating firmware and
device drivers, and completing the installation, Business Partners must also do the following:

1. After you have confirmed that the server starts correctly and recognizes the newly installed devices

and that no error LEDs are lit, run the DSA stress test. For information about using DSA, see “Dynamic
System Analysis” on page 58.

2. Shut down and restart the server multiple times to ensure that the server is correctly configured and

functions properly with the newly installed devices.

3. Save the DSA log as a file and send it to Lenovo. See “Sending DSA data to Lenovo” on page 173.

4. To ship the server, repackage it in the original undamaged packing material and observe Lenovo

procedures for shipping.

Support information for Business Partners is available at http://www.ibm.com/partnerworld.

Sending DSA data to Lenovo

Before you send DSA data to Lenovo, read the terms of use at:
http://www.ibm.com/de/support/ecurep/terms.html

You can use any of the following methods to send the DSA data to Lenovo:

•

Standard upload

:

http://www.ibm.com/de/support/ecurep/send_http.html

•

Standard upload with the system serial number

:

http://www.ecurep.ibm.com/app/upload_hw

•

Secure upload

:

http://www.ibm.com/de/support/ecurep/send_http.html#secure

•

Secure upload with the system serial number

:

https://www.ecurep.ibm.com/app/upload_hw

Removing and installing server components

173

«
...
185
186
187
188
189
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

NovaScale T820 F2

Brand: Bull Pages: 34

Brand: disguise Pages: 12

Brand: LG Pages: 100

Brand: LG Pages: 35

Brand: NEC Pages: 4

Express5800/T120e

Brand: NEC Pages: 2

Express5800/T120d

Brand: NEC Pages: 2

Express5800/T110j

Brand: NEC Pages: 32

Express5800/T110j-S

Brand: NEC Pages: 32

Express5800/T120g

Brand: NEC Pages: 40

Express5800/T110g-S

Brand: NEC Pages: 35

Express5800/T110h

Brand: NEC Pages: 40

Express5800/T110i

Brand: NEC Pages: 45

Express5800/R120g-2E

Brand: NEC Pages: 35

Express5800/R120g-1E

Brand: NEC Pages: 37

Express5800/R120g-2M

Brand: NEC Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands