Lenovo x3250 m6 Installation And Service Manual Download Page 649

Page: 649 / 696

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-801-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Unable to communicate with driver.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the DSA Diagnostic code is at the latest level.

2. Run the test again.

3. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

4. Run the test again.

5. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

6. Run the test again.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-802-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. A read error was encountered.

Recoverable

Appendix C. DSA diagnostic test results

635

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands