Lenovo x3250 m6 Installation And Service Manual Download Page 526

Page: 526 / 696

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

405-906-000 : BRCM:TestLoopbackPhysical Test Failed

A failure was detected during the loopback test at the physical layer.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

512

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands