Lenovo x3250 m6 Installation And Service Manual Download Page 648

Page: 648 / 696

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

409-906-000 : Nvidia::DiagnosticServiceProvider::Binomial Test Failed

Nvidia GPU Binomial Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA optical drive test results

The following messages can result when you run the optical drive test.

Test results for the DSA optical drive test

The following messages can result when you run the DSA optical drive test.

•

215-000-000 : Optical Drive Test Passed

Optical Drive Test Passed.

Recoverable

634

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands