Lenovo x3250 m6 Installation And Service Manual Download Page 142 | Manualshive

Page: 142 / 696

background image

contain heavy metals must not be disposed of with normal domestic waste. They will be taken back
free of charge by the manufacturer, distributor, or representative, to be recycled or disposed of in a
proper manner.

• To order replacement batteries, call 1-800-IBM-SERV within the U.S., and 1-800-465-7999 or

1-800-465-6666 within Canada. Outside the U.S. and Canada, call your support center or business
partner.

Note:

After you install the coin-cell battery, you must reconfigure the server and reset the system date

and time.

CAUTION:
When installing the lithium battery, use only Part Number 33F8354 or an equivalent type battery
recommended by the manufacturer. If your system has a module containing a lithium battery,
install it only with the same module type made by the same manufacturer. The battery contains
lithium and can explode if not properly used, handled, or disposed of.

Do not:

– Throw or immerse into water

– Heat to more than 100°C (212°F)

– Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

To install the coin-cell battery, do the following:

Step 1.

Install the new coin-cell battery. Ensure that the coin-cell battery retainer holds the battery securely.

Figure 64. Coin-cell battery installation

Step 2.

Complete the parts replacement. See “Completing the parts replacement” on page 172.

Step 3.

Start Setup Utility and reset the configuration:

a.

Set the system date and time.

b.

Set the power-on password.

c.

Reconfigure the server.

For more information, see “Starting the Setup Utility program” on page 29.

128

Lenovo System x3250 M6 Installation and Service Guide

«
...
140
141
142
143
144
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: Vxl Pages: 19

Brand: SEH Pages: 50

DLAP-201 Series

Brand: ADLINK Technology Pages: 39

Brand: Sun Microsystems Pages: 12

Brand: LOOQS Pages: 69

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 25

G4-Apex-ENTERPRISE-HW

Brand: Viavi Pages: 8

ASR-3100PP-R11A1E

Brand: Advantech Pages: 86

Brand: Advantech Pages: 110

Brand: AirLive Pages: 133

Brand: Optibase Pages: 28

TIGPT1U - Carrier Grade Server

Brand: Intel Pages: 89

Brand: Intel Pages: 80

Brand: Intel Pages: 97

Brand: Intel Pages: 108

SE7320SP2 - 800MHZ Ecc Ddr Xeon

Brand: Intel Pages: 184

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands