Lenovo x3250 m6 Installation And Service Manual Download Page 76 | Manualshive

Page: 76 / 696

background image

Optical drive problems

Table 9. Optical drive symptoms and actions

Symptom

Action

The optical drive is not
recognized.

1. Make sure that:

• The SATA connector to which the optical drive is attached (primary or

secondary) is enabled in Setup Utility.

• All cables and jumpers are installed correctly.

• The correct device driver is installed for the optical drive.

2. Run the optical drive diagnostic programs.

3. Reseat the following components:

a. Optical drive

b. Optical drive cable

4. Replace the components listed in step 3 one at a time, in the order shown,

restarting the server each time.

5. (Trained technician only) Replace the system board.

A CD or DVD is not working
properly.

1. Clean the CD or DVD.

2. Replace the CD or DVD with new CD or DVD media.

3. Run the optical drive diagnostic programs.

4. Check the connector and signal cable for bent pins or damage.

5. Reseat the optical drive.

6. Replace the optical drive.

The optical drive tray is not
working.

1. Make sure that the server is turned on.

2. Insert the end of a straightened paper clip into the manual tray-release hole.

3. Reseat the optical drive.

4. Replace the optical drive.

Hard disk drive problems

Table 10. Hard disk drive symptoms and actions

Symptom

Action

Not all drives are recognized by
the hard disk drive diagnostic
test.

Remove the drive that is indicated by the diagnostic tests; then, run the hard disk
drive diagnostic test again. If the remaining drives are recognized, replace the drive
that you removed with a new one.

The server stops responding
during the hard disk drive
diagnostic test.

Remove the hard disk drive that was being tested when the server stopped
responding, and run the diagnostic test again. If the hard disk drive diagnostic test
runs successfully, replace the drive that you removed with a new one.

A hard disk drive was not
detected while the operating
system was being started.

Reseat all hard disk drives and cables; then, run the hard disk drive diagnostic test.

A hard disk drive passes the
diagnostic Fixed Disk Test, but
the problem remains.

Run the diagnostic SCSI Fixed Disk Test. See “Running DSA Preboot diagnostic
program” on page 59.

Note:

This test is not available on servers that have RAID arrays or servers that have

SATA hard disk drives.

62

Lenovo System x3250 M6 Installation and Service Guide

«
...
74
75
76
77
78
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: Obvius Pages: 29

Brand: Buffalo Pages: 2

Brand: AIC Pages: 101

Brand: IBM Pages: 491

Brand: Goonas Pages: 13

Brand: IBM Pages: 21

callpilot 1002rp

Brand: Avaya Pages: 150

Brand: MRV Communications Pages: 65

Brand: A & T Internationale Pages: 165

Brand: Lantronix Pages: 100

Brand: Raidon Pages: 71

Brand: APLIGO Pages: 47

Brand: Inspur Pages: 84

Brand: Inspur Pages: 80

Brand: MPC Pages: 72

Brand: Gateway Pages: 226

Brand: Gigabyte Pages: 2

Brand: Yawarra Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands