Lenovo x3250 m6 Installation And Service Manual Download Page 107

Page: 107 / 696

Step 3.

Use the key to lock the security bezel to the closed position.

000000000000000

0000

0000000000

Figure 21. Locking the security bezel

Removing the PCI riser-card assembly

To remove the PCI riser-card assembly, do the following:

Step 1.

Turn off the server. Then, disconnect all external cables and remove all peripheral devices.

Step 2.

Remove the server cover. See “Removing the server cover” on page 88.

Step 3.

Grasp the blue tabs on the PCI riser-card assembly and lift the PCI riser-card assembly to release it
from the chassis.

Figure 22. PCI riser-card assembly removal

Step 4.

Disconnect any cables from the adapters on the PCI riser-card assembly.

Step 5.

Remove the adapter from the PCI riser-card assembly. See “Removing an adapter” on page 110.

Step 6.

Place the PCI riser-card assembly on a flat, static-protective surface.

Chapter 7

Removing and installing server components

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands