Lenovo x3250 m6 Installation And Service Manual Download Page 141 | Manualshive

Page: 141 / 696

background image

recommended by the manufacturer. If your system has a module containing a lithium battery,
replace it only with the same module type made by the same manufacturer. The battery contains
lithium and can explode if not properly used, handled, or disposed of.

Do not:

– Throw or immerse into water

– Heat to more than 100°C (212°F)

– Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

Note:

After you remove the coin-cell battery, you need to install a new one. See “Installing the coin-cell

battery” on page 127.

To remove the coin-cell battery, do the following:

Step 1.

Turn off the server. Then, disconnect all external cables and remove all peripheral devices.

Step 2.

Remove the server cover. See “Removing the server cover” on page 88.

Step 3.

If necessary, remove the air baffle. See “Removing the air baffle” on page 90.

Step 4.

Locate the coin-cell battery, see “System-board connectors” on page 21.

Step 5.

Remove the coin-cell battery.

Attention:

• Failing to remove the coin-cell battery properly might damage the socket on the system board.

Any damage to the socket might require replacing the system board.

• Do not tilt or push the coin-cell battery by using excessive force.

Figure 63. Coin-cell battery removal

Step 6.

Dispose of the coin-cell battery as required by local ordinances or regulations. For more
information, see the

Environmental Notices and User's Guide

on the documentation CD.

Installing the coin-cell battery

The following tips describe information that you must consider when installing the coin-cell battery.

• Follow any special handling and installation instructions that come with the coin-cell battery.

• Lenovo has designed this product with your safety in mind. The lithium battery must be handled correctly

to avoid possible danger. If you install the coin-cell battery, you must adhere to the following instructions.

Note:

In the U. S., call 1-800-IBM-4333 for information about battery disposal.

• If you replace the original lithium battery with a heavy-metal battery or a battery with heavy-metal

components, be aware of the following environmental consideration. Batteries and accumulators that

Removing and installing server components

127

«
...
139
140
141
142
143
...
»

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3250 m6

Brand: MSI Pages: 107

Brand: Patton electronics Pages: 326

UniServer R4300 G6

Brand: H3C Pages: 542

Brand: 3onedata Pages: 3

Brand: Gigabyte Pages: 120

Brand: Toshiba Pages: 28

Brand: Toshiba Pages: 204

SD-H400 - Combination Progressive-Scan DVD Player

Brand: Toshiba Pages: 291

SC10E16A1 Series

Brand: San Telequip Pages: 85

DIRECTORY SERVER 8.0

Brand: Red Hat Pages: 128

LANTIME/SHS/BGT

Brand: Meinberg Pages: 5

LANTIME M600/GPS

Brand: Meinberg Pages: 6

GV-Video Server

Brand: GeoVision Pages: 179

Horizone Mini IN00M02WEB

Brand: Eelectron Pages: 2

Brand: TAG Pages: 44

Brand: Vlinx Pages: 43

Brand: Fiery Pages: 160

Brand: Inspur Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands