Lenovo x3250 m6 Installation And Service Manual Download Page 166

Page: 166 / 696

Step 4.

Remove the screw from the power distribution board cover. Then, lift the power distribution board
cover up to remove it from the server.

Figure 90. Power distribution board cover removal

Step 5.

Reinstall the power distribution board cover or install a new one. See “Installing the power
distribution board cover” on page 152.

Installing the power distribution board cover

If you have moved the power distribution board cover, reinstall it or install a new one if the old one is broken.

To install the power distribution board cover, do the following:

152

Lenovo System x3250 M6 Installation and Service Guide

Summary of Contents for x3250 m6

























































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands

Lenovo x3250 m6, Installation And Service Manual

Search results

Summary of Contents for x3250 m6

Reviews:

Related manuals for x3250 m6

Brands by name

Popular brands