Keysight Technologies E4981A Service Manual Download Page 94

Page: 94 / 152

Chapter 6

Replacement Procedure

3/4 Rack Module Top Replacement

Tools Required

•

Torque screwdriver, TORX T20

Removal Procedure

Refer to

Figure 6-1

Figure 6-2

and for this procedure.

Step 1.

Disconnect the power cable from the E4981A.

Step 2.

Remove the handle, front bumper and rear bumper. (item 1, 2, 3 )

NOTE

To remove the handle, rotate the handle to a vertical position and pull the arms outwards.

Step 3.

Work the six TORX T20 screws (item 4) loose from the bottom.

Step 4.

Remove the 3/4 Rack Module Top.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

NOTE

Fasten the 3/4 Rack Module Top from the Rack Module Bottom in the spcified order.
(

Figure 6-3

)

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands