Keysight Technologies E4981A Service Manual Download Page 127

Page: 127 / 152

Chapter 6

125

Replacement Procedure

Front Panel, Key Pad and Key Flex Circuit Replacement

6. Re

placem

ent Pro

Front Panel, Key Pad and Key Flex Circuit Replacement

Tools Required

•

Torque screwdriver, TORX T6

•

Torque screwdriver, TORX T10

•

Torque screwdriver, TORX T20

•

Box torque wrench, 3/8 inch

•

Box torque wrench, 5/8 inch

Removal Procedure

Refer to

Figure 6-23

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Front Panel Assembly as described in

“Front Panel Assembly Removal” on

page 101

Step 4.

Remove the Inverterl Assembly as described in

“Inverter Assembly Replacement” on

page 119

Step 5.

Remove the Display Support as described in

“Display Support Removal” on page 121

Step 6.

Remove the two TORX T10 screws (item 1) fastening the Front Panel Assembly.

Step 7.

Remove the USB Assembly from the Front Panel.

Step 8.

Remove the 3/8 inch nut and washer (item 2) fastening the Binding Post Assembly.

Step 9.

Slide the Binding Post Assembly from the Front Panel Assembly.

Step 10.

Remove the Front Panel from the Key Pad, the Window EMI Shield, the Key Flex Circuit
and the EMI Shield (item 3).

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands