Keysight Technologies E4981A Service Manual Download Page 7 | Manualshive

Page: 7 / 152

background image

5

Certification

Keysight Technologies certifies that this product met its published specifications at the
time of shipment from the factory. Keysight Technologies further certifies that its
calibration measurements are traceable to the United States National Institute of Standards
and Technology, to the extent allowed by the Institution’s calibration facility, or to the
calibration facilities of other International Standards Organization members.

Documentation Warranty

The material contained in this document is provided "as is," and is subject to being
changed, without notice, in future editions. Further, to the maximum extent permitted by
applicable law, Keysight disclaims all warranties, either express or implied with regard to
this manual and any information contained herein, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Keysight shall not be
liable for errors or for incidental or consequential damages in connection with the
furnishing, use, or performance of this document or any information contained herein.
Should Keysight and the user have a separate written agreement with warranty terms
covering the material in this document that conflict with these terms, the warranty terms in
the separate agreement will control.

Exclusive Remedies

The remedies provided herein are buyer’s sole and exclusive remedies. Keysight
Technologies shall not be liable for any direct, indirect, special, incidental, or
consequential damages, whether based on contract, tort, or any other legal theory.

Assistance

Product maintenance agreements and other customer assistance agreements are available
for Keysight Technologies products.

For any assistance, contact your nearest Keysight Technologies Sales and Service Office.
Addresses are provided at the back of this manual.

«
...
5
6
7
8
9
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Kawai Pages: 66

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: janitza Pages: 12

Brand: NCTE Pages: 10

Brand: Rae Pages: 38

Brand: FlowLine Pages: 2

Brand: Eurotron Pages: 122

Brand: POSEIDON Pages: 21

Vigilant Plant MR20000

Brand: YOKOGAWA Pages: 230

Proline Promag 10D

Brand: Endress+Hauser Pages: 28

Brand: Allen Organ Company Pages: 29

Brand: Badger Meter Pages: 18

Brand: Yamaha Pages: 14

Brand: Xylem Pages: 2

Brand: X-IO Pages: 58

Brand: All-sun Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands