Keysight Technologies E4981A Service Manual Download Page 137

Page: 137 / 152

Appendix B

135

Firmware Update

Update the E4981A firmware using USB cable

B. F

irmwar

Upd

Update the E4981A firmware using USB cable

Required Equipment

•

E4981A.

•

USB cable connecting the E4981A and external controller (with type A/4-prong male
or type mini-B/5-prong male connectors depending on device used).

•

Personal Computer with I/O Libraries Suite (Windows 2000/XP).

How to update E4981A firmware using USB cable

The following is the procedure to update the E4981A firmware using USB cable.

Step 1.

Connect the USB cable from the USB terminal in your computer to the USB terminal in
the E4981A rear panel. Then turn the E4981A on.

Step 2.

Copy the following file from Keysight Technologies web site to the temporary work folder
in your computer’s HDD.

•

fw_upd.exe

Step 3.

Execute the

Command Prompt

on your computer.

Step 4.

Change the current folder to the temporary working folder with the “fw_upd.exe” file
using

command.

Step 5.

Enter

fw_upd.exe USB0::2391::2313::MY12345678::0::INSTR

command to execute the

firmware update program. The enterd value of “2391::2313::MY12345678” in the
command is USB ID of the E4981A, and the enter value of “MY12345678” is serial
number of the E4981A. Then, press the Enter key.

Step 6.

Wait a few minutes until the command prompt is displayed again.

Step 7.

Press

System

key on the E4981A front panel to check the firmware revision.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands