Keysight Technologies E4981A Service Manual Download Page 60 | Manualshive

Page: 60 / 152

background image

58

Chapter 4

Troubleshooting

Function Specific Troubleshooting

Step 3.

Press the

SYSTEM CONFIG

softkey.

Step 4.

Select the DHCP ENABLED field using the cursor keys and then press the

OFF

softkey.

Step 5.

Select the AUTO-IP ENABLED field using the cursor keys and then press the

OFF

softkey.

Step 6.

Enter the following IP address and subnet mask using the enter keys. For selecting the
MANUAL IP ADDR or MANUAL SUBNET MASK field, use the cursor keys.

IP Address: 192.168.0.1

Subnet Mask: 255.255.255.0

Step 7.

Set up the IP address/subnet mask for the external PC.

a.

Double-click “

My Computer

” icon on Windows desktop of the external PC. And

double-click

Control Panel

. The Control Panel window will appear.

b.

In the Control Panel window, double-click

Network

. The Network dialog box will

appear. In the

Configuration

tab, select

TCP/IP

(display it in revers video) and press

the

Properties

button.

c.

The dialog box appears. If

Specify an IP address

has been selected, record the IP

address and subnet mask.

d.

If the

Obtain an IP address automatically

has been selected, select the

Specify an IP

address

. Enter the IP address xxx.xxx.xxx.y and subnet mask xxx.xxx.xxx.xxx as

shown in

. The letters x represent the IP address and subnet mask of the

E4981A. The letter y is different from the IP address of the E4981A. Press the

OK

button. Then, restart the external PC.

Figure 4-6

Network Dialog Box (“IP Address” Tab)

Step 8.

By clicking “OK” button, the network settings take effect. Verify the E4981A LAN
settings and response to a command from the external computer as follows:

a.

On the external computer, click "Start" button in the Windows Start menu bar using a
mouse.

㪼㪋㪐㪏㪇㪸㫊㪼㪈㪇㪌㪌

«
...
58
59
60
61
62
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Vanguard Instruments Pages: 24

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brand: Vectornav Pages: 114

Brand: Vanguard Instruments Company Pages: 62

Brand: Vanguard Instruments Company Pages: 58

Prestige Series

Brand: Ibanez Pages: 54

Monitoring System 500 II DC

Brand: Didactum Pages: 2

Brand: Barksdale Pages: 2

AccuPoint 2 ATP

Brand: Neogen Corporation Pages: 16

Brand: A&D Pages: 24

Brand: YATO Pages: 52

Brand: Heyl Pages: 2

IMI Sensors 66212ANZ2

Brand: PCB Piezotronics Pages: 6

WJ-NX310K Series

Brand: i-PRO Pages: 18

Brand: CWT Pages: 41

Brand: Hanna Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands