Keysight Technologies E4981A Service Manual Download Page 38 | Manualshive

Page: 38 / 152

background image

36

Chapter 3

Adjustment

Safety Considerations

Safety Considerations

This manual contains NOTEs, CAUTIONs, and WARNINGs that must be followed to
ensure the safety of the operator and to keep the instrument in a safe and serviceable
condition. The adjustment must be performed by Keysight’s qualified service personnel.

WARNING

Any interruption of the protective ground conductor (inside or outside the
equipment) or disconnection of the protective ground terminal can make the
instrument dangerous. Intentional interruption of the protective ground system for
any reason is prohibited.

Warm-up for Adjustment

Warm-up the E4981A for at least 30 minute before performing any of the following
Adjustment procedures to ensure proper results and correct instrument operation.

Required Equipment

Table 1-1 on page 16

lists the equipment required to perform the Adjustment procedures

described in this chapter. Use only calibrated test equipment when adjusting the E4981A.

«
...
36
37
38
39
40
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Yamaha Pages: 8

Brand: M & I Instruments Pages: 2

Brand: Rayjet Pages: 81

Brand: Saimo Pages: 101

Brand: C.R. Laurence Pages: 4

Brand: Neogen Pages: 9

Brand: Dakota Digital Pages: 34

Brand: Value Pages: 20

Brand: NARDA Pages: 60

Brand: Xsens Pages: 12

Brand: Metrohm Pages: 81

Digalox DPM72-MPPV

Brand: TDE Instruments Pages: 8

Brand: jenway Pages: 53

Brand: Hanna Instruments Pages: 52

Brand: Campbell Pages: 20

Brand: S2Tech Pages: 58

Digital Sound Level Meter DSM-1

Brand: Nady Audio Pages: 4

Brand: CATH-TECH Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands