Keysight Technologies E4981A Service Manual Download Page 117

Page: 117 / 152

Chapter 6

115

Replacement Procedure

Power Inlet Assembly Replacement

6. Re

placem

ent Pro

Power Inlet Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T10

•

Torque screwdriver, TORX T20

•

Cutting plier

Removal Procedure

Refer to

Figure 6-17

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Cut the two cable ties (item 1).

Step 4.

Remove the two TORX T10 screws (item 2) fastening the Inlet Assembly.

Step 5.

Remove the Inlet Assembly from the Rear Panel.

Step 6.

Detach the fuse box (item 3) from the Inlet Assembly and remove the fuse.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

NOTE

Do not forget to insert the fuse in the new Inlet Assembly.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands