Keysight Technologies E4981A Service Manual Download Page 53 | Manualshive

Page: 53 / 152

background image

Chapter 4

51

Troubleshooting

Troubleshooting Using Service Function

4. T

roub

lesho

o

ting

The file location on the USB memory is as follows:

\e4981a\system\sysinfo.txt

NOTE

The system information of E4981A may be used for the purposes of support and repair by
Keysight Technologies, but will never be used for any other purposes.

To save the system information into external memory:

Step 1.

Plug a USB memory stick into the front USB port.

Step 2.

Press [System].

Step 3.

Press the

SERVICE

softkey.

Step 4.

Press the

MORE

softkey.

Step 5.

Press the

SAVE SYS INFO

softkey.

Step 6.

While the data is being saved, a "PROCESSING..." message is shown on the display. When
the data has been saved into the USB memory, a "Storing data completed." message
appears in the system message area.

Example of the System Information

The sysinfo.txt can be read by using an external computer (PC). The example of the system
information is as follows:

Example 4-1

System information

ID: Keysight Technologies,E4981A,MY12345678,A.01.00

OPT: 0

POWER CYCLE: 214

POWER ON HOURS: 746

SYSCAL REV: 1.00

SYSCAL DATE: 2008/7/23

R: Rev.1.11

CPU[1]: 0

CPU[2]: 0

SYST[1]: 0

SYST[2]: 0

SYST[3]: 0

SYST[4]: 0

DATA[1]: 0

DATA[2]: 0

DATA[3]: 0

DATA[4]: 0

OPT[1]: 0

A1[1]: -1.15601

A1[2]: +1.18401

A1[3]: +5.12900

A1[4]: +3.36400

«
...
51
52
53
54
55
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Omicron Pages: 80

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Wavetek Pages: 43

Portable Grand DGX-670

Brand: Yamaha Pages: 93

Portatone PSR-410

Brand: Yamaha Pages: 65

Brand: LumaSense Pages: 23

Brand: Det-Tronics Pages: 18

Brand: LEGRAND Pages: 5

Digital Piano CA750

Brand: Kawai Pages: 76

Brand: Keller Pages: 8

Brand: Supertech agroline Pages: 10

ACCURE 2350-GAS

Brand: ROOTECH Pages: 26

Brand: THORLABS Pages: 49

Panametrics XDP

Brand: Baker Hughes Pages: 64

Brand: IROX Pages: 8

Brand: YOSensi Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands