Keysight Technologies E4981A Service Manual Download Page 68

Page: 68 / 152

Chapter 4

Troubleshooting

Function Specific Troubleshooting

Step 12.

Use the softkeys to select the

SCANNER INTERFACE

test.

Step 13.

Press the

EXECUTE

TEST START

softkeys to execute the

SCANNER INTERFACE

test.

Step 14.

Confirm that LEDs on the scanner simulator board turn ON in accordance with the
E4981A settings displayed in the LCD.

Step 15.

Press the

TEST STOP

softkey.

NOTE

Do not execute any SELF TEST except for the Scanner Interface Test or the E4981A will
become inoperative.

Step 16.

Return the switch settings on the Interface Board to their original settings.

Softkey

Function

INCR +

Increments the test number of the Test Menu.

DECR -

Decrements the test number of the Test Menu.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands