Keysight Technologies E4981A Service Manual Download Page 110

Page: 110 / 152

108

Chapter 6

Replacement Procedure

A31 Digital Board Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T8

•

Torque screwdriver, TORX T10

•

Torque screwdriver, TORX T20

•

Box torque wrench, 5/8 inch

Removal Procedure

Refer to

Figure 6-12

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Interface Board Assembly as described in

“Interface Board Assembly

Replacement” on page 105

Step 4.

Remove the PPMC PCA as described in

“PPMC PCA Replacement” on page 107

Step 5.

Remove a 5/8 inch nut (item 1) fastening the Rear Chassis Assembly.

Step 6.

Disconnect the Fan cable from the A31 Digital Board Assembly (item 2).

Step 7.

Remove the six TORX T10 screws (item 3) fastening the Rear Chassis Assembly.

Step 8.

Remove the Digital Borad Assembly.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands