Keysight Technologies E4981A Service Manual Download Page 109

Page: 109 / 152

Chapter 6

107

Replacement Procedure

PPMC PCA Replacement

6. Re

placem

ent Pro

PPMC PCA Replacement

Tools Required

•

Torque screwdriver, TORX T8

•

Torque screwdriver, TORX T10

•

Torque screwdriver, TORX T20

Removal Procedure

Refer to

Figure 6-11

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Interface Board Assembly as described in

“Interface Board Assembly

Replacement” on page 105

Step 4.

Remove the four TORX T8 screws (item 1) fastening the A31 Digital Board Assembly.

Step 5.

Disconnect the cable from the GPIB Assembly (item 2).

Step 6.

Remove the CPU Borad Assembly.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Figure 6-11

PPMC PCA Replacement

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands