Keysight Technologies E4981A Service Manual Download Page 6 | Manualshive

Page: 6 / 152

background image

4

safety features are maintained in operational condition.

•

Dangerous Procedure Warnings

Warnings, such as the example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed.

WARNING

Dangerous voltage levels, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting this instrument.

•

Do not connect the measuring terminals to mains.

Safety Symbols

General definitions of safety symbols used on the instrument or in manuals are listed
below.

Instruction Manual symbol: the product is marked with this symbol when it is necessary for
the user to refer to the instrument manual.

Alternating current.

Direct current.

On (Supply).

Off (Supply).

In position of push-button switch.

Out position of push-button switch.

Frame (or chassis) terminal. A connection to the frame (chassis) of the equipment which
normally include all exposed metal structure.

Stand-by.

WARNING

This warning sign denotes a hazard. It calls attention to a procedure, practice,
condition or the like, which, if not correctly performed or adhered to, could result in
injury or death to personnel.

CAUTION

This Caution sign denotes a hazard. It calls attention to a procedure, practice, condition or
the like, which, if not correctly performed or adhered to, could result in damage to or
destruction of part or all of the product.

NOTE

Note denotes important information. It calls attention to a procedure, practice, condition or
the like, which is essential to highlight.

«
...
4
5
6
7
8
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: E Instruments Pages: 2

Brand: CAENels Pages: 75

TEC SourceMeter 2510

Brand: Keithley Pages: 244

Brand: Kawai Pages: 112

Brand: Saluki Pages: 312

Brand: Sanmenxia Pages: 17

Brand: SANKO Pages: 25

Brand: Samson Pages: 2

Brand: Mini Pages: 20

Brand: Teledyne Hastings Instruments Pages: 54

Brand: Kawai Pages: 64

Brand: Kawai Pages: 28

Brand: Kawai Pages: 28

Brand: Interacoustics Pages: 54

Brand: PCB Piezotronics Pages: 10

Brand: Hanna Instruments Pages: 28

Brand: Omega Pages: 26

Brand: Hach Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands