Keysight Technologies E4981A Service Manual Download Page 121

Page: 121 / 152

Chapter 6

119

Replacement Procedure

Inverter Assembly Replacement

6. Re

placem

ent Pro

Inverter Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T6

•

Torque screwdriver, TORX T20

•

Box torque wrench, 5/8 inch

Removal Procedure

Refer to

Figure 6-20

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Front Panel Assembly as described in

“Front Panel Assembly Removal” on

page 101

Step 4.

Disconnect the LCD Cable (item 1) from the Inverter Assembly.

Step 5.

Disconnect the Cable (item 2) from the Inverter Assembly.

Step 6.

Remove the two TORX T6 screws (item 3) from the Inverter Assembly.

Step 7.

Remove the Inverter with the Insulator from the Display Interface Board.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands