Keysight Technologies E4981A Service Manual Download Page 113

Page: 113 / 152

Chapter 6

111

Replacement Procedure

Plate Assembly Replacement

6. Re

placem

ent Pro

Plate Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T20

Removal Procedure

Refer to

Figure 6-14

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Front Chassis Assembly as described in

“Front Panel Assembly Removal” on

page 101

Step 4.

Remove the Rear Chassis Assembly as described in

“Rear Chassis Assembly Removal” on

page 110

Step 5.

Remove the two TORX T20 screws (item 1) fastening the 3/4 Rack Module Bottom
Assembly.

Step 6.

Remove the Plate Assembly (item 2).

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Figure 6-14

Plate Assembly Replacement

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands