UC-260 Wireless Acoustic Indicator
1 / 2
MFI51405
UC-260 Wireless Acoustic Indicator
The UC-260 can be used as a wireless indoor siren, a melody doorbell
or as a chime. It can also function as a small house alarm. The UC-260
is compatible with Jablotron wireless control panels (JA-60,
JA-63 and JA-65), JA-60 wireless detectors and RC-11, RC-40, RC-22
and RC-28 remote controls. Several triggering devices can be used
simultaneously and different melodies can be assigned to each device.
Two different sound levels can be selected. The UC-260 provides
entrance and exit delay chirps too, when used with a control panel.
Specification
Power supply
110-230 V, 50-60 Hz
Power consumption
1.5 W
Electrical protection- Class (EN60950)
II
Acoustics
8 melodies and/or 100 dB/m alarm siren
Input wireless devices
max. 8 remote controls or detectors
1 control panel JA-60, JA-63 or JA-65
Working frequency
433,92 MHz
Environmental conditions
interior
–10 to +40°C
Degree of protection
IP40 according to EN 60529
Can be operated according to ERC REC 70-03
Hereby, JABLOTRON ALARMS, declares that this UC-260
is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC and 2011/65/EU.
Original of the conformity assessment can be found at the web page
, section Technical support.
Installation
UC-260 is powered directly from a power outlet. The device should not
be installed close to any metal structures or other objects obstructing
radio signal transmission.
Enrolling of wireless components
1. Press and hold the button on the top of the UC-260.
2. Plug in the UC-260 to an outlet
and hold the button until you hear
2 beeps.
3. Release the button
– The button will begin to flash, indicating it is in
the programming mode.
4. Enrolling of components:
Doorbell button
(RC-11, RC-40, RC-22, RC-28, RC-60) can be
enrolled by pressing a button on the controller or by triggering an
input. Multiple pressing of the controller
’s button will allow you to
scroll to a desired melody.
Detector - chime
mode
(JA-60 detectors) can be enrolled by
inserting batteries into a detector. You can scroll to a desired
melody by pressing the tamper switch.
Control panel
– siren mode
(JA-60, JA-63 or 65)
– while in the
service mode of the control panel, enter code 299.
5.
Up to 8 doorbell buttons or detectors plus 1 control panel can be
used with one UC-260.
6. Exit the programming mode
by pressing the UC-260
’s button
briefly.
If you enter the programming mode the way above, all enrolled
components will be erased from the memory.
Adding components
If you want to add additional doorbell buttons or detectors or if you
want to select another melody for an existing component, than:
1. Unplug the UC-260 from the outlet
and wait for 5 seconds.
2. Plug it in again.
3. The button will light
– press it and hold it down.
4. After hearing a short beep, release the button.
The flashing
button indicates it is in the programming mode.
5. Enrolling new components
(or selecting another melody):
RC remote control
(RC-11, RC-40, RC-22, RC-28, RC-60) can
be enrolled by pressing a button on the controller or activating its
input. Multiple pressing of the controller
’s button will allow you to
scroll to a desired melody.
Detector
(JA-60 detectors) can be enrolled by inserting batteries
into a detector. You can scroll to a desired melody by pressing the
tamper switch.
Control panel
(JA-60, JA-63 or 65)
– while in the service mode of
the control panel, enter code 299.
6.
Up to 8 buttons or detectors plus 1 control panel can be used with UC-
260.
7. Exit the programming mode
by pressing the UC-260 button briefly.
Deleting components
Press and hold a red button on the UC-260 and plug the UC-260 into
the mains outlet. Hold the button until two beeps can be heard indicating
that all components have been erased.
Loudness selection
The UC-260 must be in its operating mode (plugged in).
Press and hold the button down.
After 2 sec you will hear a melody with the new loudness selected
Release the button.
This way you can toggle between a standard and a louder one.
This setting doesn’t affect the alarm siren sound.
Note:
even though this product does not contain any harmful materials
we suggest you to return the product to the dealer or directly to the
producer after usage.
